Sonoma SGR30MLP Grill Parts

Sonoma 4-Burner 30" LP gas grill

Highest quality replacement parts for your Sonoma SGR30MLP - Free USA shipping $49 or more* - No Sales Tax*

Sonoma SGR30MLP owners manual and diagrams

Diagrams & owners manual not available for grill model# SGR30MLP. If you have a manual you're willing to share, please click here to send us an email with the attached manual. Thank You!

Replacement BBQ grill parts for Sonoma model: SGR30MLP

All of the parts we have for Sonoma SGR30MLP are shown on this page. If you can't find the part you need below, click on the appropriate category button on the right side of the page. For example, if your looking for a heat indicator and there are none here, click the heat indicator button to see all we have for Sonoma grills. Knowing the dimensions of your existing part will help you find the right part.

To get the correct Sonoma SGR30MLP BBQ parts

You should measure your existing parts and compare them to what we show here. This is best done with them removed from the grill.
Verify your Sonoma model number by checking the CSA appliance tag on your grill to make sure you have the correct model number. Do not rely solely on the owners manual as these are frequently mixed up at retail stores when the grills are assembled. You'd be surprised at how many folks have the wrong owners manual.

SGR30MLP Burners

Click for photos

304 Stainless steel Infrared rear rotisserie burner with ceramic wafer for Sonoma model SGR30MLP. For use with both liquid propane (LP) and natural gas grills. 8,000 BTU. Orifice not included. Use old orifice or purchase our orifice part# CLA-VB0245 for LP, or part# CLA-VB0246 for natural gas applications.

Dimensions:

Maximum overall length, including mounting tab on one end: 17”
Maximum width: 3 3/8”
Burner box 15 3/8” x 3 3/8”
Mounting holes: 16 1/8” on center

Part Number: CLA-BL0229
Dimensions: 3 3/8” x 17”
Material: stainless steel and ceramic
Weight: 3.0

Click for photos

Stainless steel triple burner set for Sonoma model SGR30MLP. Electrodes not incuded.

Part Number: TUST3
Dimensions: 18” x 15 3/4”
Material: stainless steel
Weight: 3.5

==> All Sonoma Burners.

SGR30MLP Burner Brackets and Carryovers

Click for photos

4-Burner support and carry-over bracket. Made in USA.

Part Number: CLA-MS0265
Dimensions: 26”
Material: stainless steel
Weight: 0.75

==> All Sonoma Burner Brackets and Carryovers.

SGR30MLP Cooking Grids

Click for photos

Stainless steel cooking grids with solid 1/4” rods (set of 3) for Sonoma model SGR30MLP.

Part Number: 53S33
Dimension Front-to-Back: 17 1/2”
Dimension Side-to-Side: 27 3/8”
Material: stainless steel wire
Weight: 10.0

==> All Sonoma Cooking Grids.

SGR30MLP Heat Plates

Click for photos

Large Flavor Grid for Sonoma model SGR30MLP. Stainless steel. Only one of these are used on the grill. This part has an extended side that faces the infrared burner and acts as a heat shield. The other Flavor Grids do not have this shield.

One required per grill.
Sold individually.
Made in USA.

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use. Made in USA

Part Number: CLA-TS0072
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 1.2

Click for photos

Stainless steel Flavor Grid for Sonoma model SGR30MLP.

Part Number: SONHP1
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.6

==> All Sonoma Heat Plates.

SGR30MLP Igniter Components

Click for photos

21” wire for side burner or other applications. Both ends are female spade connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 10342-T12
Dimensions: 21
Weight: 0.05

Click for photos

Ceramic electrode with mounting bracket. For use with triple burner assembly part# SONT3 and ALTT3.

Sold individually, two (2) required
Use old screws and support plate

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-25B
Weight: 0.3

Click for photos

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

==> All Sonoma Igniter Components.

SGR30MLP Valves, Orifices, and Manifolds

Click for photos

#63 orifice for infrared burner CLA-BL0229; use on liquid propane (LP) gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VB0245
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

#55 orifice for infrared burners use on natural Gas grills. Includes brass elbow with 1/4” compression fitting.

Part Number: CLA-VB0246
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

==> All Sonoma Valves, Orifices, and Manifolds.

SGR30MLP Miscellaneous Repair Parts

Click for photos

Stainless steel electrode shield. Made in USA

Part Number: CLA-MS0091
Dimensions: 14 1/8” x 3 3/8”
Material: stainless steel
Weight: 0.4

==> All Sonoma Miscellaneous Repair Parts.

SGR30MLP Accessories

Click for photos

Universal Grid Lifting Tool

Part Number: BRGG
Weight: 1.0

Click for photos

Venturi Tube 12” Brush. Recommended by all grill manufacturers. Specially designed flexible brush to clean venturis of spider webs and other obstructions that can cause flashback fires. Stainless steel.

Part Number: VTC-B
Material: stainless steel
Weight: 0.3

==> All SGR30MLP Accessories.

BBQ Part Categories

Sonoma gas grill SGR30MLP - Sunday, Jan 26 2025

Return to Sonoma grills main page

More Sonoma grill models we have parts for
CGR27 \| CGR27LP \| CGR30 \| CGR30LP \| CGR30NG \| CGR44 \| CGR54 \| PF30LP \| PFISLP \| PFISNG \| PFSISLP \| SGIR27LP \| SGR27LP \| SGR30 \| SGR30LP \|