Charbroil 463242615 Grill Parts

Stainless Steel Burner for Lowes' Charbroil Grills for Charbroil model 463242615.

Part Number: CBP13
Dimensions: 14 7/16
Material: stainless steel
Weight: 0.45

stainless steel cross-over burner

Part Number: 05595
Dimensions: 7 7/16” x 0 3/4”
Material: stainless steel
Weight: 0.1

Stainless steel stamped cooking grids for Charbroil model 463242615. Also known as ”cooking grate, infrared emitter.” Sold as a set of three (3).

Part Number: 5S373
Dimension Front-to-Back: 17 3/16”
Dimension Side-to-Side: 30”
Material: stamped stainless steel
Weight: 5.6

Cast iron cooking grids for Charbroil model 463242615. Porcelain treated, flat matte finish. Sold as a set of three (3).

Part Number: 69373
Dimension Front-to-Back: 17 1/16”
Dimension Side-to-Side: 28 1/2”
Material: matte cast iron
Weight: 19.4

Stainless steel Heat Tent for Charbroil model 463242615. Sold individually.

Part Number: 92171
Dimension Front-to-Back: 15 1/4”
Dimension Side-to-Side: 1 13/16”
Material: stainless steel
Weight: 0.6

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ignition electrode.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 04450
Dimensions: 3 5/16” x 0 7/8”
Weight: 0.1

Round 2 3/8” diameter heat indicator, includes one wing nut and one locking nut.

• Requires minimum 3/8” mounting hole
• Single 1 3/8” probe
• Threaded portion of probe stops at 1/2” from base
• See photo for details

Part Number: 00012
Dimensions: 2 3/8” x 2 3/8”
Weight: 0.1

Universal Grid Lifting Tool

Part Number: BRGG
Weight: 1.0

Venturi Tube 12” Brush. Recommended by all grill manufacturers. Specially designed flexible brush to clean venturis of spider webs and other obstructions that can cause flashback fires. Stainless steel.

Part Number: VTC-B
Material: stainless steel
Weight: 0.3